注释
.png "Cntl+X 导致工作位置在 0.8c 上丢失？ #250"){kind=avatar}
成员
|
这是设计和 gcode 定义。G92 不是工作坐标状态，而是定义为坐标偏移量，只要系统是，就会被重新设置。请使用实际工作坐标系g54-59。这些是使用 g10 命令设置的并且是持久的。 |
.jpg "Cntl+X 导致工作位置在 0.8c 上丢失？ #250"){kind=avatar}
作者
|
G10 就像一个魅力！ 谢谢 |
Cntl+X 导致工作位置在 0.8c 上丢失？ #250
|
这是设计和 gcode 定义。G92 不是工作坐标状态，而是定义为坐标偏移量，只要系统是，就会被重新设置。请使用实际工作坐标系g54-59。这些是使用 g10 命令设置的并且是持久的。 |
|
G10 就像一个魅力！ 谢谢 |
运行 0.8c 注意工作位置在 cntl+x 之后被覆盖
使用一个简单的场景复制它，
启动 grbl，移动到 10,10 将工作位置设置为 0,0,0
再移动 10,10 然后 crtl+X 导致工作位置
丢失。
请在下面找到日志
?<Idle,MPos:0.000,0.000,0.000,WPos:0.000,0.000,0.000>
G90
ok
G21
ok
G00 X10 Y10 F200
ok
?<Run,MPos:0.144,0.144,0.000,WPos:0.144,0.144,0.000>
? <Run,MPos:9.819,9.819,0.000,WPos:9.819,9.819,0.000>
……
?<Idle,MPos:10.000,10.000,0.000,WPos:10.000,10.000,0.000>
?<Idle,MPos :10.000,10.000,0.000,WPos:10.000,10.000,0.000>
G92 X0 Y0 Z0
ok
?<Idle,MPos:10.000,10.000,0.000,WPos:0.000,0.000,0.000>
?<Idle,MPos:10.000,10.000 0.000,WPos:0.000,0.000,0.000>
G90
ok
G21
ok
G00 X10 Y10 F200
ok
?<Run,MPos:10.006,10.006,0.000,WPos:0.006,0.006,0.000>
?<Run,MPos:10.212,10.212,0.000,WPos:0.212,0.212,0.000>
?<Run,MPos:20.000,20.000,0.000,WPos:10.000,10.000,0.000>
….
<Idle,MPos: 20.000,20.000,0.000,WPos:10.000,10.000,0.000>
?<Idle,MPos:20.000,20.000,0.000,WPos:10.000,10.000,0.000>
cntlX
Grbl 0.8c [‘$’ for help]
ok
?<Idle, MPos:20.000,20.000,0.000,WPos:20.000,20.000,0.000>