看起来 FluidNC 的 ESP3D 中的主轴按钮不起作用。我可以通过按 M3 按钮从 CNCJS 启用主轴（RelayModule），但不能从 Web 界面启用。Flood 和 Mist 等其他按钮在 Web 界面上工作。
这是低优先级的，很高兴将来有时间。
“速度图最大速度为 0”有一个错误，但如果我为继电器模块更改它，它就会停止工作。

[MSG:INFO: Restarting]
ets 2016 年 6 月 8 日 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv: 0x00，hd_drv：0x00，wp_drv：0x00
模式：DIO，时钟 div：1
负载：0x3fff0018，len：4
负载：0x3fff001c，len：1044
负载：0x40078000，len：10124
负载：0x40080400，len：5856
条目 0x400806a8
[MSG： INFO: FluidNC v3.2.8]
[MSG:INFO: Compiled with ESP32 SDK:v3.3.5-1-g85c43024c]
[MSG:INFO: Configuration file:config.yaml]
[MSG:ERR: Speed map max speed is 0. 使用default]
[MSG:INFO: Machine 6 Pack StepStick XYZ]
[MSG:INFO: Board 6 Pack]
[MSG:INFO: I2SO BCK:gpio.22 WS:gpio.17 DATA:gpio.21]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cs_pin:gpio.5 detect:NO_PIN]
[MSG:INFO: Stepping:I2S_stream Pulse:4us Dsbl Delay:0us Dir Delay:1us Idle Delay:250ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: X 轴(150.000,450.000)]
[MSG:INFO: Motor0]
[MSG:INFO: Standard Stepper Step:I2SO.2 Dir:I2SO.1 Disable:I2SO.0]
[MSG:INFO: Neg Limit gpio.33:low:pu ]
[MSG:INFO: Y 轴 (-150.000,150.000)]
[MSG:INFO: Motor0]
[MSG:INFO: Standard Stepper Step:I2SO.5 Dir:I2SO.4 Disable:I2SO.7]
[MSG:INFO:负限制 gpio.32:low:pu]
[MSG:INFO: Z 轴 (-150.000,150.000)]
[MSG:INFO:Motor0]
[MSG:INFO: Standard Stepper Step:I2SO.10 Dir:I2SO.9 Disable:I2SO.8]
[MSG:INFO: Neg Limit gpio.35:low]
[MSG:INFO: Kinematic system : 笛卡尔]
[MSG:INFO: 继电器主轴 Ena:NO_PIN Out:gpio.14 Dir:NO_PIN]
[MSG:INFO: 使用主轴继电器]
[MSG:INFO: Flood coolant I2SO.24]
[MSG:INFO: Mist coolant I2SO .27]
[MSG:INFO: Probe Pin: gpio.39]
[MSG:INFO: Connecting to STA SSID:XXXXXXX]
[MSG:INFO: Connecting.]
[MSG:INFO: Connecting..]
[MSG:INFO: Connected – IP 是 192.168.1.102]
[MSG:INFO: WiFi on]
[MSG:INFO: Start mDNS with hostname:http://fluidnc.local/%5D
[MSG:INFO: SSDP Started]
[MSG:INFO: HTTP started on端口80]
[MSG:INFO: Telnet started on port 23]
Grbl 3.2 [FluidNC v3.2.8 (wifi) ‘$’ for help]